Home > Training Program > Class Descriptions

Class Descriptions

Woodward Governor Training - 2017 Class Descriptions

Woodward hands-on training is ideal for those who need to understand how Woodward controls and associated accessories operate. GCS certified, factory-trained instructors offer practical, theoretical training in a closed-loop environment.

  • 2301 A/D or 2301 D/E Load Sharing &
    Speed Control

    Class # 100 - 3 days, $1470 per person


    Learn the operation, installation and adjustments of 2301A (Analog) and the 2301D or E (Digital) Load Sharing Speed Control. Understand how the 2301A and 2301D or E control, actuators, and their associated accessories allow their engines to operate together, either on or off the infinite bus (utility). Hardware and software configuration / monitoring will be explained and connected to a loop test set.

  • 505 / 505E Steam Turbine Control

    Class #107 - 3 days, $1470 per person


    Review Woodward 505/505E steam turbine control theory and turbine parameters, installation, wiring, operating procedures, programming, and troubleshooting. The hands on portion includes programming, adjustments and troubleshooting techniques on the 505 connected to the simulator with specifically designed examples. Operate the control within a closed loop test set.

  • 723 PLUS Digital Speed Control

    Class #103 - 3 days, $1470 per person


    Woodward 723PLUS control is a configurable control for prime movers. Both the hardware and software will be covered in class. During the course, the control will be programmed and monitored with Woodward Watch Window and a hand-held programmer. The control will be operated using a closed loop test set to simulate an engine.

  • DSLC-2 and MSLC-2 Controls

    Class #101A - 2 days, $980 per person


    Learn more about the basics of power management. This course will focus on the Woodward DSLC- 2? & MSLC- 2? controls including theory, installation, operation, maintenance plus hands-on programming, adjustments, and troubleshooting techniques.

     

  • E3 Gas Engine Control System

    Class #117 - 2 days, $1470 per person


    This class covers theory, installation, maintenance and troubleshooting of the Woodward E3 air-fuel ratio control in Lean Burn Trim or Full Authority Stems. The control is tested in a close-loop system.


  • easYgen 3200 Power Management Control

    Class #115A - 2 days, $980 per person (English)
    Custom Class (Call or Send Request) (Spanish)


    Learn more about the basics of power management using the Woodward easYgen 3200 control system. The course covers theory, installation, programming, operation and maintenance of the easYgen 3200 control system using actual controls. Hands-on training includes time for programming, adjustments and troubleshooting techniques.

  • easYgen 3500 Power Management Control

    Class #115B - 3 days, $1470 per person


    Learn more about the basics of power management using the Woodward easYgen 3500 control system. The course covers theory, installation, programming, operation and maintenance of the easYgen 3500 control system using actual controls. Hands-on training includes time for programming, adjustments and troubleshooting techniques.

  • EGCP-3 LS / MC Power Management Control

    Custom Class (Call or Send Request)


    Learn about the Woodward EGCP-3. This class will begin with an introduction to the basics of power management. The installation, programming, troubleshooting, and operation of the EGCP-3 will be covered and class members will gain hands-on experience in programming the control.

     

  • Peak 150 Steam Turbine Control

    Class #106 - 2 days, $980 per person


    Woodward Peak 150 digital steam turbine controls is used in mechanical drive applications. Hardware, software, and programming will be demonstrated; the control connected to a closed loop test set. Learn how the Peak 150 control, actuators, and their associated accessories allow turbines to operate together, either on or off the infinite bus (utility) or operating a mechanical drive.

  • PG Mechanical Governor Basics
    (PGA, PGG, PG-PL, PGG)

    Class #109 - 3 days, $1470 per person


    This class will give you opportunity to learn about PG mechanical governor. In this class you will learn theory, installation, operation and maintenance of the governor. Calibration and troubleshooting done using the test stand.

  • ProTech TPS, GII and SX Overspeed Protection

    Class #108 - 2 days, $980 per person


    Woodward ProTech GII, the ProTech TPS and ProTech SX are speed Safety Devices for steam turbines. This class is designed to explain the operation, theory, installation, programming, and maintenance. The hands-on portion will include time for programming, adjustments, and troubleshooting techniques.

     

  • UG-8 / UG-40 Mechanical Governor

    Class # 108 - 2 days, $980 per person


    This class will give you opportunity to learn about UG governor. In this class you will learn theory, installation, operation and maintenance of the governor. Calibration and troubleshooting done using the test stand.